WHEEL PRESS TO OPEN AND CLOSE THE SCREW-ON BACKS OF ALL
Horotec® wheel press
HOROTEC
Wheel press to open and close the screw-on backs of all types of cases.
Compatible with all Horotec® dies and case holders.
Size : 200 x 200 x 400 mm.
Active filters
Horotec® wheel press
HOROTEC
Wheel press to open and close the screw-on backs of all types of cases.
Compatible with all Horotec® dies and case holders.
Size : 200 x 200 x 400 mm.
SUPPORT FOR ASSEMBLE/DISASSEMBLE THE OSCILLATING WEIGHT BOLTS, CAL. 7700 / 7750 / A07111 / A07161 / A07271
ASSORTMENT OF STEEL DIES FOR OPENING/CLOSING CASES WITH SCREWED-ON BACKS TYPE RX, 8 PIECES / Ø 18.5…36.5 mm
HANDS REMOVING TOOL WITHOUT CONTACT WITH THE DIAL, 3 PINS Ø 0.15 - 0.60 - 1.00 mm + 3 EXTRACTORS 0.60 - 1.45 - 2.10 mm + BASE
REVERSIBLE SCREW-ON DIE FOR FITTING VERY DOMED CRYSTALS, Ø 65 mm
REVERSIBLE SCREW-ON DIE FOR FITTING VERY DOMED CRYSTALS, Ø 20 mm
ASSORTMENT FOR INCABLOC, 6 PUSHERS + 7 STAKES, AXLE Ø 3 mm
HANDS EXTRACTOR FOR TOOL MSA05.125, WIDTH 1.45 mm / VERSION 2
SCREW-ON DIE FOR CLOSING CASES WITH SNAP-ON BACKS, Ø 52-55 mm
PDF
RACK-PRESS FOR OPENING/CLOSING CASES WITH SCREWED-ON BACKS, VERSION RED SUCTION DIES
The press is equipped with two handles that can be declutched to facilitate their positioning according to the desired angle :
(1) Lateral handle allows to lower or to lift the toothed rack in order to have a better control of the pressure applied to the
case back during unscrewing/screwing ;
(2) Upper handle (mobile) is used to unscrew/screw the case back.
Compatible with all HOROTEC® dies and case holders, see pages 07-25...07-28 and 07-30...07-32.
The press is equipped with two handles that can be declutched to facilitate their positioning according to the desired angle :
(1) Lateral handle allows to lower or to lift the toothed rack in order to have a better control of the pressure applied to the
case back during unscrewing/screwing ;
(2) Upper handle (mobile) is used to unscrew/screw the case back.
Contents :
07.367-P Rack-press 4.000
07.367-A (3) Red suction case holder 0.130
07.333 (4) Assortment of 7 red suction dies 0.140
Spare part :
07.367-R Lateral spring for press, Ø 18 x H 13 mm 0.005
ASSORTMENT OF STEEL DIES FOR OPENING/CLOSING CASES WITH SCREWED-ON BACKS TYPE BR, 6 PIECES / Ø 34 - 35 - 35.5 - 36 - 37 - 38 mm
Horotec® hands fitting press
HOROTEC
Hands fitting press, 4 broaches.
Delivered with stakes equipped with PEEK tips (doesn’t mark the hands).
For hands : hours (Ø 1.35 mm), minutes (Ø 0.95 mm), seconds (Ø 0.30 mm) and 1 decentred stake.
Size : 160 x 100 x 130 mm.
STEEL DIE WITH 12 SIDES FOR OPENING/CLOSING CASES WITH SCREWED-ON BACKS TYPE PAN, Ø INT. 30.60 / Ø EXT. 40 mm
STEEL DIE WITH 12 SIDES FOR OPENING/CLOSING CASES WITH SCREWED-ON BACKS TYPE PAN, Ø INT. 35.55 / Ø EXT. 45 mm
Hands removing press, without contact with the dial.
This press allows removing safely the hands fitted on a dial, making
possible the extraction of hands without damaging the dial
Contents :
- 1 press 05.129-01
- 1 hand tool 05.128-02
- 1 base for extractors and pins 05.129-02
- 1 plate
- 3 extractors 05.129-060, 05.129-150 and 05.129-250
- 3 pins 05.128-015, 05.128-060 and 05.128-100.
Other sizes of extractors upon request.
Hands removing press, without contact with the dial.
This press allows removing safely the hands fitted on a dial, making
possible the extraction of hands without damaging the dial.
Spare parts :
05.129-01 Press 0.660
05.129-02 Base 0.090
05.128-02 (1) Hand tool 0.020
05.128-015 Pin with spring Ø 0.15 mm 0.002
05.128-060 (2) Pin with spring Ø 0.60 mm 0.002
05.128-100 Pin with spring Ø 1.00 mm 0.002
05.129-060 (3) Hands extractor, notch 0.60 mm 0.003
05.129-150 Hands extractor, notch 1.50 mm 0.003
05.129-250 Hands extractor, notch 2.50 mm 0.003
Optional extractors with columns :
05.128-B Hands extractor with columns, 0.60 x 3.80 mm 0.003
05.128-C Hands extractor with columns, 1.45 x 3.80 mm 0.003
05.128-D Hands extractor with columns, 2.10 x 4.70 mm 0.003
Optional extractors without columns :
05.129-060C Counter hands extractor, notch 0.60 mm 0.003
05.129-200 Hands extractor, notch 2.00 mm 0.003
PRESS FOR RIVETING AND MILLING DELIVERED IN BOX (FULL VERSION), 89 PUNCHES, 2 MILLING POINTS, 6 STAKES, 4 CHUCKS P4.5, 2 LOCKNUTS, 1 ROD FOR BROACH AND 2 HEX KEYS
PIN PUNCH SUPPORT FOR PRESSES MSA07.367 /07.368 /.07.369, STAINLESS STEEL / Ø 8 x L35 mm
Hands removing press with fine adjustment, without contact with the
dial.
This press allows removing safely the hands fitted on dial,
guaranteeing their extraction without damaging the dial.
Contents :
- 1 press MSA05.131-P
- 1 hand tool MSA05.128-02
- 1 base MSA05.129-02 for extractors and pins
- 5 extractors MSA05.129-060, MSA05.129-060C, MSA05.129-150,
MSA05.129-200 and MSA05.129-250
- 3 pins MSA05.128-015, MSA05.128-060 and MSA05.128-100.
Universal correcting press, facilitates the work of milling, drilling, tapping,
deburring, chamfering, reaming, etc.
Wide range of tightening chucks P 4.5 type to be mounted on the broach,
fine adjustment of the working height.
Large stainless steel work plate and dies adapter.
Compatible with all HOROTEC® screw-on dies.
Contents :
- 1 press
- 1 tip 1° angle MSA13.010-01
- 1 tip 2° angle MSA13.010-02
- 1 tightening chuck P 4.5 type Ø 3 mm MSA03.875-300
- 1 dies adapter MSA13.010-AD
- 1 ring with knurled knob MSA13.010-BA
- 1 broach for tightening chucks P 4.5 type MSA13.010-BR
- 1 Allen key MSA13.010-CL
- 1 stainless steel table Ø 60 mm MSA13.010-TA.
Small sized press, suitable for screw-on and snap-on dies.
Contents :
– 1 assortment of 12 screw-on dies MSA07.104
– 1 press MSA07.130
– 1 upper adaptor for screw-on dies MSA07.130-A
– 1 reversible lower adaptor for screw-on and snap-on dies MSA07.130-B
– 1 broach with wheel MSA07.130-C
– 1 packaging box
– 1 certificate of authenticity
– 1 cleaning cloth.
MINI-PRESS WITH WHEEL FOR OPENING/CLOSING CASES WITH SCREWED-ON BACKS, CARBON COLOUR
Mini professional precision press. Small and robust, built in steel and aluminium.
Equipped with removable and adjustable watch holder with 4 Delrin® dies to hold the watch cases surely and horizontally.
First fit the case in the watch holder and then unscrew the case back with the adjustable jaws holder.
Excellent frontal, lateral or plunging view.
Top wheel Ø 75 mm.
Contents :
– 1 adjustable jaws holder MSA07.344, maximum opening 65 mm
– 2 round jaws MSA07.323-A
– 2 flat jaws MSA07.323-B
– 2 square jaws MSA07.323-C
– 2 knurled jaws MSA07.323-D
– 1 adjustable case holder with 4 Delrin® dies MSA07.360-A
– 1 gasket for broach MSA07.320-A
– 1 packaging box
– 1 certificate of authenticity
– 1 cleaning cloth.
PRESS WITH LARGE WHEEL FOR OPENING/CLOSING CASES WITH SCREWED-ON BACKS, CARBON COLOUR
Professional precision press, heavy and robust for opening/closing screw-on case backs of all types of watches.
Large ergonomic top wheel Ø 160 mm for screwing/unscrewing with no effort.
Centre threaded broach with precise blocking ring.
Solid steel supporting pillars covered with anti-skid and ergonomic synthetic material, for right and left handed.
Base equipped with 4 anti-skid feet.
Contents :
– 1 adjustable jaws holder MSA07.344, maximum opening 65 mm
– 2 round jaws MSA07.323-A
– 2 flat jaws MSA07.323-B
– 2 square jaws MSA07.323-C
– 2 knurled jaws MSA07.323-D
– 1 adjustable case holder with 4 Delrin® dies MSA07.360-A
– 1 packaging box
– 1 certificate of authenticity
– 1 cleaning cloth.