Horotec® wheel press

HOROTEC

Wheel press to open and close the screw-on backs of all types of cases.

Compatible with all Horotec® dies and case holders.



Size : 200 x 200 x 400 mm.

SUPPORT FOR ASSEMBLE/DISASSEMBLE THE OSCILLATING WEIGHT BOLTS, CAL. 7700 / 7750 / A07111 / A07161 / A07271

ASSORTMENT OF STEEL DIES FOR OPENING/CLOSING CASES WITH SCREWED-ON BACKS TYPE RX, 8 PIECES / Ø 18.5…36.5 mm

HANDS REMOVING TOOL WITHOUT CONTACT WITH THE DIAL, 3 PINS Ø 0.15 - 0.60 - 1.00 mm + 3 EXTRACTORS 0.60 - 1.45 - 2.10 mm + BASE

REVERSIBLE SCREW-ON DIE FOR FITTING VERY DOMED CRYSTALS, Ø 65 mm

REVERSIBLE SCREW-ON DIE FOR FITTING VERY DOMED CRYSTALS, Ø 20 mm

ASSORTMENT FOR INCABLOC, 6 PUSHERS + 7 STAKES, AXLE Ø 3 mm

HANDS EXTRACTOR FOR TOOL MSA05.125, WIDTH 1.45 mm / VERSION 2

SCREW-ON DIE FOR CLOSING CASES WITH SNAP-ON BACKS, Ø 52-55 mm
PDF

Universal brass tool to remove glasses from Ø 10 to 45 mm, delivered with standard plate, 0.70 mm thickness
Reference : 4266
Swiss made Top seller
Removes and inserts immediately, crystals without dis-assembling the watch.
Will not damage the crystal.
For any unbreakable ­crystal without tension ring.
Useful for removing immediately a watch glass for:
- replacing the glass
- steam removing
- getting at the hands.

Tool for fitting
unbreakable crystals
with and without
tension ring
Die-cast alloy press, matt
chromed, with opening in the
base to allow the insertion of
metal bracelets fixed to watches.
Not suitable to fit mineral
crystals.
See other models.

RACK-PRESS FOR OPENING/CLOSING CASES WITH SCREWED-ON BACKS, VERSION RED SUCTION DIES

The press is equipped with two handles that can be declutched to facilitate their positioning according to the desired angle :
(1) Lateral handle allows to lower or to lift the toothed rack in order to have a better control of the pressure applied to the
case back during unscrewing/screwing ;
(2) Upper handle (mobile) is used to unscrew/screw the case back.

Compatible with all HOROTEC® dies and case holders, see pages 07-25...07-28 and 07-30...07-32.

The press is equipped with two handles that can be declutched to facilitate their positioning according to the desired angle :
(1) Lateral handle allows to lower or to lift the toothed rack in order to have a better control of the pressure applied to the
case back during unscrewing/screwing ;
(2) Upper handle (mobile) is used to unscrew/screw the case back.

Contents :

07.367-P Rack-press 4.000
07.367-A (3) Red suction case holder 0.130
07.333 (4) Assortment of 7 red suction dies 0.140

Spare part :

07.367-R Lateral spring for press, Ø 18 x H 13 mm 0.005

ASSORTMENT OF STEEL DIES FOR OPENING/CLOSING CASES WITH SCREWED-ON BACKS TYPE BR, 6 PIECES / Ø 34 - 35 - 35.5 - 36 - 37 - 38 mm

Rubber ball to open and close all types of screw-down case backs.

Inflated rubber ball to open and close all types of screw-down case backs. Inexpensive, easy-to-use this case opener allows most watches to be opened and will not leave marks. Ø 67 mm.

Horotec® hands fitting press

HOROTEC

Hands fitting press, 4 broaches.

Delivered with stakes equipped with PEEK tips (doesn’t mark the hands).

For hands : hours (Ø 1.35 mm), minutes (Ø 0.95 mm), seconds (Ø 0.30 mm) and 1 decentred stake.



Size : 160 x 100 x 130 mm.

4-pin stem for fitting the needles

Interchangeable plastic cleats.
Base: Ø 31 mm. Precise pin guidance.
High positioning accuracy.