REVERSIBLE SCREW-ON DIE FOR FITTING FLAT MINERAL CRYSTALS, Ø 57-60 mm

REVERSIBLE SCREW-ON DIE FOR FITTING VERY DOMED CRYSTALS, Ø 65 mm

REVERSIBLE SCREW-ON DIE FOR FITTING VERY DOMED CRYSTALS, Ø 20 mm

ASSORTMENT OF STEEL DIES FOR OPENING/CLOSING CASES WITH SCREWED-ON BACKS TYPE RX, 8 PIECES / Ø 18.5…36.5 mm / WITH HANDLE

ASSORTMENT FOR INCABLOC, 6 PUSHERS + 7 STAKES, AXLE Ø 3 mm

HANDS EXTRACTOR FOR TOOL MSA05.125, WIDTH 1.45 mm / VERSION 2

SCREW-ON DIE FOR CLOSING CASES WITH SNAP-ON BACKS, Ø 52-55 mm
PDF

ASSORTMENT OF REVERSIBLE SCREW-ON DIES FOR FITTING CRYSTALS WITH TENSION RING, 15 PIECES / Ø 15...45 mm

REVERSIBLE SCREW-ON DIE FOR FITTING FLAT MINERAL CRYSTALS, Ø 40-35 mm

ASSORTMENT OF REVERSIBLE SCREW-ON DIES FOR FITTING BEZELS, 11 PIECES / Ø 25-26...45 mm

PRESS FOR CLOSING CASES WITH SNAP-ON BACKS, WITH 9 SCREW-ON DIES MSA07.106

JAW FOR SCREWED-ON BACK CASES TO USE WITH JAWS HOLDER MSA07.344, ELONGATED POINT, REINFORCED ROUND

CASE HOLDER WITH RED SUCTION CUP FOR PRESSES MSA07.368 /07.369

ASSORTMENT OF RED SUCTION DIES FOR OPENING/CLOSING CASES WITH SCREWED-ON BACKS, 10 PIECES / Ø 16...55 mm

Universal brass tool to remove glasses from Ø 10 to 45 mm, delivered with standard plate, 0.70 mm thickness
Reference : 4266
Swiss made Top seller
Removes and inserts immediately, crystals without dis-assembling the watch.
Will not damage the crystal.
For any unbreakable ­crystal without tension ring.
Useful for removing immediately a watch glass for:
- replacing the glass
- steam removing
- getting at the hands.

Tool for fitting
unbreakable crystals
with and without
tension ring
Die-cast alloy press, matt
chromed, with opening in the
base to allow the insertion of
metal bracelets fixed to watches.
Not suitable to fit mineral
crystals.
See other models.

PRESS ALONE FOR CLOSING CASES WITH SNAP-ON BACKS, SEE MSA07.131

RACK-PRESS FOR OPENING/CLOSING CASES WITH SCREWED-ON BACKS, VERSION RED SUCTION DIES

The press is equipped with two handles that can be declutched to facilitate their positioning according to the desired angle :
(1) Lateral handle allows to lower or to lift the toothed rack in order to have a better control of the pressure applied to the
case back during unscrewing/screwing ;
(2) Upper handle (mobile) is used to unscrew/screw the case back.

Compatible with all HOROTEC® dies and case holders, see pages 07-25...07-28 and 07-30...07-32.

The press is equipped with two handles that can be declutched to facilitate their positioning according to the desired angle :
(1) Lateral handle allows to lower or to lift the toothed rack in order to have a better control of the pressure applied to the
case back during unscrewing/screwing ;
(2) Upper handle (mobile) is used to unscrew/screw the case back.

Contents :

07.367-P Rack-press 4.000
07.367-A (3) Red suction case holder 0.130
07.333 (4) Assortment of 7 red suction dies 0.140

Spare part :

07.367-R Lateral spring for press, Ø 18 x H 13 mm 0.005

ASSORTMENT OF STEEL DIES FOR OPENING/CLOSING CASES WITH SCREWED-ON BACKS TYPE BR, 6 PIECES / Ø 34 - 35 - 35.5 - 36 - 37 - 38 mm