Fixed steady for longer work pieces
Especially for boring. Also required if the tailstock cannot be used to "counter". Up to Ø 40mm.

Flapwheels of standard corundum

Elastic and adapt to the contours of the work piece being processed. For machining inaccessible spots. Shaft Ø 3.0mm.

For wood and fibreboard: HSS wood router cutters

For wood and fibreboard: HSS wood router cutters

For wood and fibreboard: HSS wood router cutters

For wood and fibreboard: HSS wood router cutters
HSS wood router cutters

For wood and fibreboard. Clean relief grinding for good work results and surface quality. High stability. Shafts 3.2mm.

HANDS REMOVING TOOL WITHOUT CONTACT WITH THE DIAL, 3 PINS Ø 0.15 - 0.60 - 1.00 mm + 3 EXTRACTORS 0.60 - 1.45 - 2.10 mm + BASE

Hot wire cutter THERMOCUT 12/E


Also for cutting free in thick Styrofoam sheets for Diorama model railway construction. For the manufacture of any profile.

Other application areas: Architecture modelling, prototype construction, for designers, decorators, or for fine work on construction insulation. And of course for classical model building.

Stable frame with pivotable fixing element at top and extendable lower wire fixing. Maximum total extension 200mm. Maximum work piece height 150mm.

Cutting wire temperature infinitely variable. With a little practice, you can achieve optimum cuts depending on the material density and thickness. Usually at medium temperatures and without too much pressure. Heat-up time 1 second. Complete with five deformable cutting wires 285 x 0.85mm.

Technical data:
12V. 50W. Cutting wire temperature controllable from approx. 150 - 350 °C. We recommend MICROMOT mains adapters as of a capacity of 2A for operation.

PDF

Largueur des mors 60 mm. Ouverture 42 mm.
Longueur totale 100 mm.

For torques of 0.35 - 2Nm. Due to rocker switch for on/off/reverse also ideal for cutting threads.

Small, light and easy to handle. A chuck facilitates acceptance of all bit shanks of and up to 6.5mm (also for standard 1/4" bits). Housing of glass-fibre reinforced POLYAMIDE. Complete with 16 inserts of chrome molybdenum steel.


Slot: 0.3 x 1.5 / 0.35 x 2 / 0.4 x 2.5mm
Philips: Size 0 and 1
TX: T 6, T 8 and T 10
Allen key, internal: 3 - 3.5 - 4 - 4.5 - 5mm
Allen key, external: 1.5 - 2 and 2.5mm


Technical data:
Direct voltage 12 - 18V. 50W. Torques of 0.35 - 1.0Nm (the sixth stage bypasses the clutch and yields approx. 2Nm). Length 200mm. Weight 415g. We recommend the use of MICROMOT mains adapters of at least 2.0A.

NO 28 690



See us on YouTube!



Note:
The bit holder shown here (50 x 76 x 15mm - 2 pieces without bits), usable
for holding rotating bits with shaft of Ø 2.35 - 3.0 and 3.2mm is available as

Pressing in, pressing out, riveting, imprinting, edging, bending of wires and sheets. Embossing, beading and crimping of easy to form materials.


With 5 cylindrical pressing tools (surface hardened) being inserted into the toothed rack and fixed with a knurled screw: Ø 3 - 4 - 5 - 6 and 8mm. One each semi-spherical profile Ø 3 and Ø 9mm as well as a 60° square prism for bending sheet metal. The counterpart is an easily adjustable, hardened revolving plate with all required holes and bottom dies for the above-specified pressing tools.

Toothed rack at one front end with 6mm bore for use of the 8 bottom dies for the above-specified pressing tools. 5mm bore at the other front end for use of all commercially available riveting tools: simply wind up the toothed rack, take it out and reinsert it upside down.

Force of pressure approx. 1,000N (100kg). Maximum stroke of toothed rack with inserted tool 65mm, above revolving plate 50mm. Solid steel arm with 120mm throat. Ground base plate of steel, 80 x 190mm with an 8mm centre and two fastening bores. Weight approx. 2,800g.